
using calculation result as input in counter log
I have an issue when trying to use result from calculation as input in Counter Log.
I have several "Operating Time" loggers which I use to track for how long each floor heating element have been enabled and recalculate that in energy used for floor heating. I use Calculation function to add values from multiple "Operating Time" loggers to add whole floor heating energy consumption in one total value. Issue occurs when I try to use result of Calculation as input in Counter Log. Calculation is working just fine - I have checked it, but when I select that Calculation as input in Counter log, I get "cyclical reference detected" error in bOS Client. As far as I can see Counter Log is working, but I keep getting "cyclical reference detected" error.
Any ideas?

DSC, Change zone names
Anyone know where I can find or how to change text for zones that appears in the bOS Client. For example by clikking *1 and your code, you will enter the menu ''bypass zones''. With the horizontal buttons you can scroll all zones. However this text does not correspond and seems to be default from the example.


Special character in HTTP device URL
Hello,
I am trying to access an HTTP API endpoint with GET request. It works from different kinds of clients (Chrome, Postman, etc.), but in bOS I get "Error connecting to device" error.
The only thing special about the request is the URL, which contains a "special" character, the colon :. This is because I can query data from a device which can be identified by its MAC address in the URL.
Has anyone experienced anything similar?
Thanks!

Johnson Controls vent unit
Hello,
Does anyone manage Johnson Controls ventilation unit via Bacnet? Does it work good or bad?
Our customer wants to manage Johnson Controls huge ventilation station in offices and ventilation controllers are Johnson Controls IOM and Johnson Controls FEC. As I understood, we have to connect IOM controllers via cat6 cable and connect it via bacnet in bos configurator, then I have to find which addresses has managing functions.
Maybe I have to connect it other way?
Will be thankful for any advise.
Regards,
Artjom

Floor heating control
What do you use to control floor heating? I bought a
R4DCB08 8-channel RS485 DS18B20 Sensor Board MODBUS RTU, but the temperature value every now and then drop down to 0°C and I don´t know why. And for the valves DANFOSS ‑ Z‑Wave Hydronic Controller HC5, didn´t get that one to work either. So I am looking för a better solusion.

How to
I have 2 variables Double (setpoints) A and B. When I change the value in one I want the following rule. A can´t be smaller than B and B can´t be bigger than A . Any ideas?

Bticino Myhome
Hi, I have already seen in the description that it works for the F454 but, please, could you confirm whether or not it is compatible with the Bticino F453 server? I have a client with this model, I have made several tests and there is no way it works and I don't know if I am doing something wrong or if it is simply not compatible.
Thanks for your help. Regards
Pablo

Modbus read value problem
Dear
I am working on an energy measurement project for a customer, in which I intend to implement Comfortclick/bOS as the management system.
I have established a modbus connection between an energy measurement device from Finder and the bOS. I simultaneously noticed that the measurement (voltage, current and power) shown on the Finder display differs from the reading obtained by the bOS which is slightly higher.
Settings:
Connection Type: Serial
Serial Transmission Mode: RTU
Low Word First: False
Low Byte First: False
Data Format: LittleEndian
Write Function Type: WriteSingle
Read Function Type: ReadSingle
Modbus Table: InputRegisters
Data Format: Signed32Bit (to power) and Unsigned32Bit (to voltage and current)
Scale Factor: 1
Use Status Address: False
Readcyclically: True
Please, could you help me with the configuration in order to get the correct reading?
Thanks,
Eduardo

IOS client connection (new customers)
we are facing in the last week a problem for new customers with IOS to connect to the client. we have the latest version 4.9.17.
it tries to connect for few seconds and come back to the server lists.
we tried also with the manual configuration, still same behavior.

ip relay
Hello,
I would like to control a Web Relay (Controlbyweb) from Jigsaw.
which device should I use?
relay ip address: 10.10.10.84
login: admin
pw : password
on command: http://10.10.10.84/state.xml?relay1State=1
off command: http://10.10.10.84/state.xml?relay1State=0
Thanks for your help
Customer support service by UserEcho