Hello everyone.

I have a question. Has anyone tried to use "Denon AVR" driver to control the Marantz SR7015 receiver. If so, which Remote Port should be set, because on 5000 I get "Error connecting to device. No response from xxx.xxx.xxx.xxx:5000”.

Regards

Hi,

I'm trying to turn on/off a light bulb. It's not working. It shows me that the device is connected. I have cheked the ip of my knx and i have selected "true" in the value tab.What elce should i do?

Hello,

We have noticed that when the iPad screens are locked no sound is played (e.g. from an event). However, Android devices do play sounds when the screen is locked.

The iPad screens cannot dim down without locking, the client is expected to have the screen on at all times which is inconvenient during night time. And if the screen locks, no sound is played.

May we expect a correction in the iOS client app or some kind of screensaver (much like Loxone)?

I'm getting brightness values from a Jung weather station on the Jigsaw. The display does not change when the station value changes. If I do a group value read in ETS6, then the value displayed in jigsaw also changes.

I don't see what to do to make the display follow the values? I would not like to force the refresh of the values on the weather station.

I'm trying to cumulate the results from each "Operating time" on each thermostat.

Each of them calculates the time the floor heating is active.

I'm then getting "Cyclical reference" from the calculation task.

Anyone know why this happens ?

I don't have it all the time, for example I had floor heating on 3 rooms activated for 10h, but one of the rooms activated for 6h of them, and when that room activated it started triggering those alerts, and when all rooms stopped heating up, it stopped triggering the errors.

To resume:
- Each thermostat has an Operating time task
- A Calculation task (A) is adding up all the values returned by each Operating time
- Every 24h I'm saving that calculated value in a Analog Log (C)

- Then I have another Calculation task (B) which get the values from (A) and removes the Day Max from (C)
- Then another Analog Log (D) gets the value from (B) every 5 minutes and show it in a graph 

And ComfortClick is triggering alerts about Cyclical references thrown by (A)

I checked ip multiple times, It's correct. I'm using only local one. On all devices it works fine on browser, but client doesn't want to work. I don't know what to do anymore.

Hello,

is it possible to change lightning scene dimming bar step from 10% to 5% or 1%?

Thanks for your help.

Kind regards.

Hi,

I have installed the Sensibo library, I put my API key and the device ID. The instructions are very easy to understand what to do, but it doesn't work. Have I left anything out?

It works perfectly from the device's own app.

I have tried to create a new Api key and it doesn't work either.

I get this message: Forbidden (403) POST:/asStates?apikey=

Can you help me, please?

Thank you very much, best regards

Hello, 

I tried to install bOS client on an iPad with iOS 9.3.5 ; that's the latest version supported on this iPad, I cannot upgrade to a newer version. 

I got the message saying that the latest bOS client version was not compatible with this iOS version, which is strange as in the app compatibility section it says that it requires iOS 8.0 or greater. 

I managed to upload an old version of bOS client, but that's not good as I won't get the latest updates. Any ways the latest bOS client version can still be compatible with iOS 8 and greater ? This is very useful to use old and cheap second hand iPad that are still working very well. 

thanks, 

François 

I have a number of Fibaro z wave blind and dimmer devices. I have an issue where the devices report Device not responding.

The command does eventually get executed however it causes a delay.

Any ideas how to resolve this problem or what could cause it?

Thanks