Enter forum description here ...
0

connect an eBus-ethernet interface

Mecat SAS 8 years ago 0

hallo

i have a VMC equipped with an ethernet interface.

i can give you operating instruction about its tcp-ip protocol .

my idea is to connect it trough your mod bus device, buti tried without success.


the device is connecyed but parameters can't be read or written....


i would be pleased if you can check the instructions to understand if my idea can be implemented


thanks 


regards 



0
Under review

License revoked after register

Fernando Castellar 8 years ago in bOS Server updated by Ahmed Ali 2 years ago 4

Hello! I was trying to try the free license and I registered my controller. But I couldn't assign the dynamic ip (ports are opened, but it says server couldn't do it.. don't remember the message), so I tried to disconnect and connect again to set it again. It asked me to register the controller again, so I removed the first one and registered it again, and when I tried to load it with the Configurator, I got a "License revoked". I don't know why it asked me to register the same controller again... but I'm sure it's my fault. How can I get back my free license? Thank you!

0
Under review

KNX ETS file

Andrea Pedrotti-Ferrari 8 years ago in Devices / KNX updated by ComfortClick Support 8 years ago 2

I've received a ETS file but the extension is *.knxproj

How can I convert this in a esf file?


Thank you 


Andrea

0

HEX tof TEXT

imperialbms 8 years ago in Devices / Basic 0

Jestem nowy i mam problem z wyświetlaniem aktualnego tekstu ze wzmacniacza DENON AVR. Tekst jest wyświetlany tylko w formacie HEX, czy wiesz, ile wartości można przekształcić w tekst?A.

0
Under review

Machine ID is change. After Upgrade bOS

sutin piyayodilokchai 8 years ago in bOS Server updated by waller bean 5 years ago 4


Hello,


I upgrade bOS Server + bOS Config + bOS Client  from 4.1.0  to 4.3.6  in PC.


After upgrade  in bOS Configurator it show not register and Machine ID is change.

  I try register but it show already register.

I uninstall all and start version 3.0.76 and up to 4.1.0   and copy backup  license.bin   

It have same problem(Machine ID is change)



Could you help ?

Thank you

0
Under review

3D floors map

Andrea Pedrotti-Ferrari 8 years ago in bOS Configurator / Themes updated by ComfortClick Support 8 years ago 1

Hello


Is it possible to know with which software do you have created the 3D maps of floors in your examples?


Thank you so much and kind regards


Andrea

0

Variable Cylic Sending of Commands

Lee Douglas 8 years ago in Devices / Http updated by Ricardo Pinto | visiontech pt 8 years ago 4

To reduce traffic, I generally set commands to send cyclically at around 5 minute intervals.

In certain circumstances, I would want to "boost" that to get 30 second responses temporarily to closely monitor conditions.

Is there a way to Send Cyclically on a variable time period?

0

Hunter Douglas PowerView blinds on bOS?

Michael Markham 8 years ago in Devices / Other updated 8 years ago 2

I'd like to control some Hunter Douglas PowerView blinds and I'm curious if anyone has figured out how to do that.  I'd appreciate your ideas.


Michael

0
Under review

Displaying IP Camera on an Amazon Echo Show?

Michael Markham 8 years ago in Devices / Cameras updated by Mike Stacey 7 years ago 3

I've successfully connected to an IP Camera using bOS.  Now, I'd like to be able to show it on an Amazon Echo Show, but it doesn't look like Alexa Skills support showing IP Cameras.


Has anyone had any luck doing this?

Thanks,

Michael

0
Under review

PIN code for locking operation

Ricardo Pinto | visiontech pt 8 years ago in bOS Configurator / Themes updated 8 years ago 2

Hi,


I've found a minor bug with the function "PIN code for locking the access to function" on controls.


Scenario:


My first theme panel is Home. And I also have a separated panel group, called Zones, and inside that panel group I have my house compartiments.


On the first it's Hallway. On the third it's Living room.


In each of this panels, I have certain controls where I've set a PIN code for locking the access to function of those controls for testing (e.g. hallway light and living room light).


When entering Zones panel, it goes to the last panel I've used (Living room). So far so good.


In Living room panel, I touch the PIN code protected living room light. It asks for PIN code. I decide not to enter the code, and press the upper right cross. It goes back to my Home panel. Strange...


Let's say that I enter again on Zones, it goes to Living room. Then I press to go to Hallway, where I touch the PIN code protected hallway light. I press the upper right cross of the PIN panel, it goes back to the Living room panel. Strange... Either way, while I was sent back to the Living room panel, if I try to do the same on the living room light, then I'm sent back to the Home panel as previously stated.


So basically, exiting the PIN code panel, doesn't save the last panel visited.


Best regards