The integration using the available HTTP example no longer works properly and the following happens:

- every two minutes the connection is established

- Lasts about 30s and turns off again

- I can't find any parameter with these values in the configuration

- during the 30s I can give commands, for example on/off, but after that it's not possible, although sometimes I can (it's random).

- The response message is "ok" when the connection is achieved and "TooManyRequests" when there is no connection.

Can you help please

Hi,

I've devices in my network using the local IP that should get automatic login, so that in the case of a device restart, just opening the browser will show the CFC interface.

I saw some other reports that suggested *YEARS* ago an URL with Demo?user= but it's no longer working.

Is there a supported way to do so?

Hey

Please fix the buggy color palet settings in CC

example 
red 60

green 40

blue 20

brigthness 100

if i turn the brightness 50% down in Client

it should go to 

red 30

green 40
blue 10

but usually the brightness value goes to 0 on some devices, it should be done with a division not substraction calculation

The color picker in BosConfig has the white plack vertical bar, this works brilliantly. please make the improvement.

Also, increase the step size for the picker for the client app, 10 is not enough to get results

Hello, I'm currently looking for a way to play a pre-recorded audio file on bOS through Sonos speakers. Do you have any examples of how to do this or any setup instructions? Thank you.

Hello. So, i'm trying to connect a Shelly 2.5 in relay mode (2 channels). I want to control channels, which works fine, to get the Switch value (if the switch it's on or off) and to find out the consumption on any channel. (in case one switch it's on, but the consumption is 0, it's means there's a problem, and i want to message the client that the lamp it's broken). I can see in subscription de actual value, in all my necessary, but i really don't know how to put the value from subscriber, into the parser. (ex: The instant consumption from the led bulb, from subscriber, into consumption panel value) . I'm a MQTT beginner, don't really know how it's works, but i try to do my best. 

Thank you very much!

Trying to connect to shelly cloud and can't understand what i'm making wrong.

with curl i'm using :

curl -X POST https://shelly-24-eu.Shelly.cloud/device/status -d "auth_key=XPTO&id=c45bbe6a3221"

and i got the json answer.

How can i program it in comfortclick?
Thanks

Hello. So, I just included a Shelly RGBW2 on my project, and got this error. The program works just fine, but i get constantly this error. Ideas what can I do to solve that? Thanks.

Hi Guys,

I have a small display issue and don't know how it could be fixed from within the configurator and need the expert view on it. Wondering if it could be a bug...

To explain, I created some visual view for a  PV installation, for me to easily identify if I sending or pulling load from the grid. I've therefore programmed some colored coded field showing the situation

The idea is to have nothing displayed when there is no transfer between the house and the grid, programmed as such

If in principle it work well, I have sometime (most of the time in fact) the arrows remaining visible as well as the consumption box back color, while I'm expecting to see nothing else than the page background...

Any idea on how I could get this fixed and get rid of the "afterglow" effect ?

Thanks for any tip.

Good morning, 
I have an NVR video recorder that can send HTTP GET commands. I would like to send commands 
to Comfortclick to turn on devices based on camera detection.
the commands that NVR can send are of the type:
http://ip address:port/saia-irc/alarm_send?open_door

where open_door I added it

However, I cannot connect it with Comforclick, via RPC

Can anyone help me?

A thousand thanks

I run comfortclick configured scenes with the press of a KNX button. It would be handy if I could run the same scene inverted (to turn off the specific lights for example)