Enter forum description here ...
0
Under review

RGB colorpanel brightness value

Allar Valksaare 9 months ago updated by ComfortClick Support 9 months ago 2

Hey

Please fix the buggy color palet settings in CC

example 
red 60

green 40

blue 20

brigthness 100

if i turn the brightness 50% down in Client

it should go to 

red 30

green 40
blue 10

but usually the brightness value goes to 0 on some devices, it should be done with a division not substraction calculation

The color picker in BosConfig has the white plack vertical bar, this works brilliantly. please make the improvement.

Also, increase the step size for the picker for the client app, 10 is not enough to get results

0
Under review

Hello, I'm currently looking for a way to play a pre-recorded audio file on bOS through Sonos speakers.

LÊ NHÂN 9 months ago in Devices / Sonos updated by Ricardo Pinto | visiontech pt 9 months ago 4

Image 4887

Hello, I'm currently looking for a way to play a pre-recorded audio file on bOS through Sonos speakers. Do you have any examples of how to do this or any setup instructions? Thank you.

0

What i'm doing wrong?

Alexandru Dumbravă 9 months ago in bOS Configurator / Devices updated 9 months ago 14

Image 4874

Image 4875Image 4876Image 4877Image 4878

Hello. So, i'm trying to connect a Shelly 2.5 in relay mode (2 channels). I want to control channels, which works fine, to get the Switch value (if the switch it's on or off) and to find out the consumption on any channel. (in case one switch it's on, but the consumption is 0, it's means there's a problem, and i want to message the client that the lamp it's broken). I can see in subscription de actual value, in all my necessary, but i really don't know how to put the value from subscriber, into the parser. (ex: The instant consumption from the led bulb, from subscriber, into consumption panel value) . I'm a MQTT beginner, don't really know how it's works, but i try to do my best. 

Thank you very much!

0

Shelly Cloud Connetion Error

Francisco Oliveira 9 months ago in Devices / Http updated by Jürgen Jürgenson 9 months ago 3

Trying to connect to shelly cloud and can't understand what i'm making wrong.

with curl i'm using :

curl -X POST https://shelly-24-eu.Shelly.cloud/device/status -d "auth_key=XPTO&id=c45bbe6a3221"

and i got the json answer.

How can i program it in comfortclick?
Thanks

0
Under review

Shelly RGBW2 Error connecting to device. Object reference not set to an instance of an object.

Alexandru Dumbravă 9 months ago in bOS Configurator / Devices updated by ComfortClick Support 9 months ago 5

Hello. So, I just included a Shelly RGBW2 on my project, and got this error. The program works just fine, but i get constantly this error. Ideas what can I do to solve that? Thanks.

Image 4860

0
Under review

visual bug ?

Fabien Fuster 9 months ago in bOS Client updated 9 months ago 9

Hi Guys,



I have a small display issue and don't know how it could be fixed from within the configurator and need the expert view on it. Wondering if it could be a bug...

To explain, I created some visual view for a  PV installation, for me to easily identify if I sending or pulling load from the grid. I've therefore programmed some colored coded field showing the situation

Image 4856

Image 4857

The idea is to have nothing displayed when there is no transfer between the house and the grid, programmed as such

Image 4858

If in principle it work well, I have sometime (most of the time in fact) the arrows remaining visible as well as the consumption box back color, while I'm expecting to see nothing else than the page background...


Image 4859

Any idea on how I could get this fixed and get rid of the "afterglow" effect ?


Thanks for any tip.

0

command HTTP GET

marco 10 months ago in Devices / Http updated 10 months ago 7
Good morning, 
I have an NVR video recorder that can send HTTP GET commands. I would like to send commands 
to Comfortclick to turn on devices based on camera detection.
the commands that NVR can send are of the type:
http://ip address:port/saia-irc/alarm_send?open_door

where open_door I added it

However, I cannot connect it with Comforclick, via RPC

Can anyone help me?

A thousand thanks
0
Under review

Is it possible to run an inverted scene?

Pavlos Laskas 10 months ago updated by Ricardo Pinto | visiontech pt 10 months ago 3

I run comfortclick configured scenes with the press of a KNX button. It would be handy if I could run the same scene inverted (to turn off the specific lights for example)

0
Under review

I am currently unable to reboot my Colibri Z-Wave servers.

APP MOD 10 months ago in bOS Server updated by ComfortClick Support 10 months ago 1

Hello,

I am currently unable to reboot my Colibri Z-Wave servers. The only way to fix this is to power cycle them. Do you have any solutions for this problem?

0

No response: Read 1/2/1 Devices\KNX\Ground

Sebastian Goff 11 months ago in Devices / KNX updated by Jürgen Jürgenson 11 months ago 1

Hello, all, I’ve got an issue where the integriti Alarm within a building. When turned off it has an output that then goes to an input of Knx which then operates outputs through the Knx. I am using a comfort click controller and for some reason I’m getting this error, but it only happens once and after attempting to arm disarm after the first time it works fine anyone got any ideas what would cause this?

Devices\KNX\Ground Floor|Ground Floor Security|Ground Floor Alarm on/off

26/02/2024 7:10 AM

No response: Read 1/2/1 Devices\KNX\Ground Floor\Ground Floor Security\Ground Floor Alarm on/off.