Hello,

I was wandering if inverters from Solar Edge are being support in same way as SMA inverters are supported.

See link to website: https://www.solaredge.com/us/products/pv-monitoring#/

Regards,

Fred

How do i change the date to a UK format i.e. dd/mm/yyy and not mm/dd/yyy

I have a D-Link camera DCS-930L, I know is a lame camera, but I'm not able connect to the camera, I'm using this link http://admin:admin@192.168.220.103/mjpeg.cgi with VLC client and works, with Chrome too works and with FireFox too.

BOS Config always set to false Online and Streaming vars.

Any idea?.

Camera config

Username:admin

Password:admin

IP:192.168.220.103

Video Size:640:480

JPEG source:--

Refresh time:1000 (default)

Mode:Direct (I have tried all modes)

WanIP:--

MJPEG Source: mjpeg.cgi (tried winth slash before name)

MPEG Source:-- (too tried with video.cgi

Best Regards

Hello. I ran into problem with onvif configurator in bOS. I click on configurator and see all camera but if I try to add it I enter Name and Password and get bad login error. And name and password work on other onvif program. Please help.

I have analog data loggers which records temeperatures in each room. 

I use that data to plot graphs. For some time now graphs simple wont plot any more in bOS Client (It was working before)

All data is normally logged (I see all new logs in bOS config in each Data logger, but graphs just won't show in bOS client.  

Hi,

I'm using Clickatell SMS API, together with Tasks (Httprequest) to send notifications from Comfortclick system. It's working great, but I'm looking forward to use line breaks in sent text.

Clickatell uses %0a as line break. The problem is that %0 is also used as property values on Comfortclick.

Is there another way to use property values beside %x, or use any kind of delimiter?

Thanks

Dears

every time I open the setting proprieties of eth included Z Wave device I got the following error message:

In my case the integrated device used is the Fibaro ZWave plus smoke sensor. Can you fix it please?

Regards

Marco

Hi,

We need to do an action wherein when anyone press the bell button on the video intercom, the lock relay ( in z wave ) gets triggered. Please assist !

MCO home relays are getting added in jigsaw z wave but the issue is with the feedback ( status ). We have used jigsaw z wave and also the UZB stick 

but still no success. The same stick over any other server or computer gives feedback for MCO home relays. Can anyone please comment ?

I am trying to integrate Modbus Thermostat ( Produal HLS 44 ) with Jigsaw Z wave via RS 485 ( RTU ). The register details are mentioned below :-

Holding Register Address 1 ( 40001 ) = FAN SPEED CONTROL WRITE

Holding Register Address 2 ( 40002 ) = SET POINT WRITE

Input Register Address 18 ( 30018 ) = SET POINT BY USER

Input Register Address 19 ( 30019 ) = FAN CONTROL BY USER

Those Address were verified using MODSCAN 32 and found to be correct.

Now in jigsaw, the scenario is different. The setup was :-

ACTUALLY ADDRESS 18 IS FOR SET POINT BUT  I AM GETTING THE SET POINT IN ADDRESS 17 ( 18 - 1 )

SIMILARLY ADDRESS 19 IS FOR FAN SPEED AND I AM GETTING IN ADDRESS 18 ( 19 - 1)

So what we have seen is for input register, we need to deduct -1 with the address mentioned in datasheet. 

REGARDING THE HOLDING REGISTER 1 AND 2, IT IS NOT WORKING. I AM ABLE TO GET DATA FROM INPUT REGISTER BY DEDUCTING THE ADDRESS BY 1. BUT I AM NOT ABLE TO WRITE ANYTHING IN HOLDING REGISTER. 

ALSO THE VALUE FROM INPUT REGISTER IS LIKE 280, 275, 220. WE NEED THE VALUE LIKE 28, 27.5, 22 ( divided by 10 ). 

CAN YOU PLEASE SUPPORT ?