I want to make scenes that will run related the sunshine. mean 20 min before sunshine scene-1, 20 min after sunshine, scene-1, 2 hours after sunshine scene-3, etc. 

Anyone ideas how to make it? 

thank you, 

German - DiLight

How is possible to switch between different themes without logout / login?

Hello everyone 

My screen resolution is 2560*1600

in bOS configurator when I put panel or page size same as my screen size its become too much big in bOS client !

why it doesn’t match ?

my current setting for this situation  is 1024*600 but in bOS configurator it coming small and hard to work with, and no option for zoom in or out ! 

any ideas ?

I need to send data to serial port on HEX format, but in the end of packet I need to calculate the the XOR of Packet and SUM of packet. Can You explain how can I do it?

* the data is an integer.

Hello,

I'm getting many "error connecting to KNX device".

On my first system (Grinder), this is happening from times to times, for a very short period of time (<1 min). 

This is not impacting the good operation of the system, except if this happening when bOS needs to issue a KNX command, but that's very rare, and then I noticed an impact only once.

I thought that maybe this was linked to my IP network that needed some troubleshooting.

But I've got another system, a KNX Jigsaw, for which the KNX error connecting to device is occurring every 2 minutes ! The KNX interface being incorporated into the Jigsaw, this can't be an issue with my environment. 

I'm not using KNX on this Jigsaw, so I just disables the KNX interface, and problem was fixed for me. 

Still I would like to understand how to fix these "error connecting to device" incidents. 

I'm also getting them from times to times for all IP-connected devices: global Caché, Philips Hue, Denon amplifier, etc... 

Thanks,

François 

Hello,

I'm using scenes with all my Z-Wave devices (about 20 of them). Scenes on a room by room basis are working ok. But when I wanted to do the classical "turn off all the lights in the house" when leaving, I got a couple of lights remaining ON, while they were shown as off on bOS. (I'm using a KNX Jigsaw with a Z-Wave USB dongle).

I added delays everywhere (in the scenes, and in the program that is calling all "OFF" scenes on a room by room basis) ; it improved a lot reliability of my "All off" scenario. Still, one or two lights remained ON while shown as OFF. 

A solution is to run the "All off" twice, but that's not very nice, and it's taking quite some time with all the delays I've added. 

So, I can understand that sometimes Z-Wave commands get lost, but I'm struggling to understand why a "OFF" command updates bOS status to "OFF" for a given device, while the device is still on, which means that no "OFF status" has been sent to the controller. 

I'm also wondering how scenes are working, i.e. do they take into account device acknowledgment ? Do they re-try to issue the order if they don't get correct device acknowledgment ?

I'm also using scenes with KNX on another system, and they are working perfectly fine. 

Thanks in advance for your explanations,

François 

Hello. 

I will need help regarding connection to sledgehammer server. Yesterday at the office I was connected with my office desktop P.C. Today I am in the project trying to change IP either to DHCP or in fixed IP. I have connected my Lap and the server via a switch I set 192.168.2.22 for my lap and the server has from yesterday 192.168.2.50. Now in the project I am trying to find it manually via bOS configurator and  I cannot find it with searching. I have conne cted the ethernet port of the server that is under USB port and I cannot find it . Also how I am going to change the default port  from 443 to another. And how  I am going to have access remotly for maiking changes if needed? 

I need a help cause I am at project right now .

Thank you in advance

I am facing a problem cause its the first time I am using Sledgehammer Server . The problem is that via bos Configurator I select the IP/interface automaticlly after searching but when I am trying to just turn on /off a light I am getting an error message saying that device is not connected. I am testing the same channel with USB / knx interface and its working Any help?

We have created allready Scenes in ETS and what I would like to know is how I am going to just call each scene? The scenes Group addreses are allready imported in bOS configurator. Also I would like to create some time tasks, To turn On and Off specific lights which I will  select in specific hours every day. Is it possible and how?

Thank you

Hello, what I need to do is to create for a Hotel 3 buttons for each room. One for Do not disturb , one for Make Up my Room and one for Room Service. I have allready created the tasks. and connected in each room. These messages will appers in Reception's central P.C. which will running bOS client. When reception see the message for each room will have the possibility to send fixed answers to each room and a confirmation that received the customer's message . I forgot to say that each room will have an Android Tablet to send the commands to the system. Is it possible to make something like this? Also inside the room we have install 3 push buttons that customer can press and select one of the 3 choices above.

Thank you in advance