I´m trying to use Thermostat Task but I would like to Change Setpoint Temperatura with a KNX Value, is it possible?

Thank´s to All

Have anyone any idea why i have this message? 

Hi

Clicking on the z-wave "Node Settings" button for a device in Devices\Z-Wave brings up the script error message shown below.

This happens for all z-wave devices. I'm running bOS on a Jigsaw device, configurator on Windows 7 and all are fully up to date with latest ComfortClick releases. I can access and browse the internet from my PC. Can you help please? 

I am not sure how  to  configure http  > Boolean with below  url /api 

I have to pass  l1498904289859 to open window  http://192.168.2.109:8080/send?deviceMac=b4430dd11511&codeId=l1498904289859 Close window  l1498900850560 http://192.168.2.109:8080/send?deviceMac=b4430dd11511&codeId=l1498900850560

using  browser  to enter  url its working  and  programme  > set the  http request also work  

Dears

I see that in one of the last BOS version in the ModBus device has been introduced two new configuration settings: Read Function Type and Write Function Type.

I want to understand more how those 2 setting work: which address are written or read  at once instead separately (if I select write or read multi)? This is not clear to me… If we suppose to get only 1 modbus device connected with slave address 1 and it contains many address for eg 10, 11, 13, 20, 21, 25 and 110 (all are coils).  Is the Bos software going to write or read once all the address from 10 to 110? From the time point of view instead? If the read interval (in the BOS  Modbus confi g page) is 100 ms, does  it mean that Bos software will read or write all  the previous address data (10, 11, …, 110) in 100 ms (instead taking 100 ms each as was before)?

Regards

Marco

Hi,

Does any one can help how to configure modbus device in order to read meeters (e.g. L1 Voltage)?

I can reed some value but something is wrong with coding.

Here you have information from the manual (mull manual: http://eastrongroupco.hk02.057321.com/data/uploads/Eastron_SDM530-Modbus_protocol_V1_1.pdf)

The format for each byte in RTU mode is:

Coding System: Data Format:

Error Check Field: Framing:

8-bit per byte 4 bytes (2 registers) per parameter.

Floating point format ( to IEEE 754) Most significant register first (Default). The default may be changed if required -See Holding Register "Register Order" parameter. 2 byte Cyclical Redundancy Check (CRC) 1 start bit 8 data bits, least significant bit sent first 1 bit for even/odd parity (or no parity) 1 stop bit if parity is used; 1 or 2 bits if no parity

Data Coding All data values in the SDM530-Modbus smart meter are transferred as 32 bit IEEE754 floating point numbers, (input and output) therefore each SDM530-Modbus meter value is transferred using two Modbus Protocol registers. All register read requests and data write requests must specify an even number of registers. Attempts to read/write an odd number of registers prompt

the SDM530-Modbus smart meter to return a Modbus Protocol exception message. However, for compatibility with some SCADA systems, SDM530-Modbus Smart meter will response to any single input or holding register read with an instrument type specific value.

The SDM530-Modbus can transfer a maximum of 40 values in a single transaction; therefore the maximum number of registers requestable is 80. Exceeding this limit prompts the SDM530-Modbus to generate an exception response.

Data transmission speed is selectable between 2400, 4800, 9600,

1.2 Input register

Input registers are used to indicate the present values of the measured and calculated electrical quantities. Each parameter is held in two consecutive16 bit register.The following table details the 3X register address, and the values of the address bytes within the message. A (*) in the column indicates that the parameter is valid for the particular wiring system. Any parameter with a cross(X) will return the value zero. Each parameter is held in the 3X registers. Modbus Protocol function code 04 is used to access all parameters.

I get Cyclical referens detected every time I enable a Program in task.

Some times I get no error. but mostley I get.

NO matter of what I run inside the program, I get the message.

But the program do whats it suppose to do.

Hi.

I want to setup that if a specific light is switched on between 01.00 and 07.00 it only stays on for 10minutes. Any hints in configuring this in bOS configurator? Wich task? Is it operating time, Schedule, or Timer?

Hi,

I have problem with several zwave devices even with Fibaro which usually worked properly with other soft. e.g. Fibaro KeyFob (can not inlclude properly - all tabs are empty), Greenwave Powernode 6 (problems with power metering). Do you have the same issues. What are the steps to solve it.