Scada view
I need to link a scada visualization of another server with a frame of comfortclick. The example is a Logic machine visualization. I enter this link (http://user:password@192.168.1.200/scada-vis/#87) but it doesn´t works. Are there another way?
json problem with decode answer message with space
Hello,
I try to get the value with the basic device and UDP request.
The answer is in json and the answer is correct you can see below an example
{
"ID": "2",
"State": 1,
"Error1": 0,
"Error2": 0,
"Plug": 3,
"AuthON": 0,
"Authreq": 0,
"Enable sys": 1,
"Enable user": 1,
"Max curr": 0,
"Max curr %": 1000,
"Curr HW": 13000,
"Curr user": 63000,
"Curr FS": 0,
"Tmo FS": 0,
"Curr timer": 0,
"Tmo CT": 0,
"Setenergy": 0,
"Output": 0,
"Input": 0,
}
When I try to read the data with the space for exemple "Enable sys" I have the error "Error parsing received data. : Unexpected character while parsing path:"
How to decode the value with space ?
I try somes codes for space but nothing work.
Can you help me please ?
UART
Hello.
I have a Grinder module, and I would like to connect a Solar Inverter via UART. In the Grinder module, I have connected the CP2102 adapter to the USB port, bOs recognizes it perfectly in the COM3 port. According to the solar inverter documentation, the communication is UART, 115200bps, 8bits data, 1 stop bit, no parity. The COM3 port, so I have configured it. But I can't get a response from the inverter. I have tried all the combinations on the bos, but I cannot receive data. Any suggestion???
Thanks...
task.scene
Hi, could i know how to set the 1byte fan speed (aircon mode) group address in the task. Scene? so I can change the setting in the scene function page.
Unable to set up dimming - KNX Gira
Hello!
I'm an amateur DIY without any prerequisites to programming. However, I'm trying to figure out why I'm not able to create a dimming function with bOS Client through a Jigsaw server.
I have a 20 year old KNX system consisting of GIRA components and a newly installed Jigsaw server as interface. Everything is working fine with the old GIRA touch panels such as light switches, dimming and scenes. My dimmers are TRONIC dimmeaktor 20-500w and DIMinBOXX DX1.
I'm able to create light switches ON/OFF but not any dimming functions. There's no response after creating the control buttons.
Is my system to old, or does it have anything to do with the true/false value settings?
If any of you would attempt to help me, bear in mind that my competence level is very low, so keep it simple, please.
ETS 6 return error on bus test
Hello.
I have problem with ETS 6 returning error on bus test, when I try lets say IP interface it is working fine. But both interfaces works with ETS 5
Show confirmation button not work properly on cancel
Hello
I have a Hormann Garage Door with Hormann KNX Gateway where I have option for going Up and Down.
For this I create two buttons. One for Up and one for Down. When I press Up button I set show confirmation to true and I added a pin to avoid Garage Door opening by mistake since from there you can enter directly in my house.
These is my confirmation setting.
When I press button bellow confirmation appear
Now come my problem.
If I put the pin everything is working fine and door is opening
If I press cancel (X button from right up corner) dialogue gone but instead to have same Garage Panel it go at main Panel.
So in case of aborting I should remain in same page.
Any idea if this is a bug and how I can fix it?
Best Regards
Valentin
Ping to other IPs
Hello,
I have a client who asks me about the possibility of being able to PING with the bOS system on an external IP to get a signal if the external IP interface is not responding.
Can we manage this functionality with bOS?
Can we send an http string to be able to perform this function?
Can you send me an example?
Best regards
Giordano Olmi
Customer support service by UserEcho