How can We translate EventTypes on Schedules for Dusk , Night , Dawn ....

I would like to know if could comfortclick  read my project from a house with 3 floors ? 

In this house I´m using two line couplers, connecting first floor to second and second to third

I have a push button in level one that connect with actuator on level two, they are conected through a line coupler. Does Comfortclick read this information and make it work ?

Hello David,

I have a customer who asks me if it is possible to control the red button on the LG remote.

In the current controls I don't find it available.

Another customer asks me if it is possible to call the other apps directly.

Now I can call Netflix directly.

Is there any way to call Now?

Giordano

Hello, 

I'm trying to connect bOS configurator directly to the server, i.e. not using the public address. Of course the PC running bOS configurator is on the same LAN than the server. 

In the configurator I create a profile manually, indicating the server IP address. But I'm getting the "Error connecting to server" message. 

An automatic profile with the server name does connect, but it is connecting from the outside (i.e. the PC goes on the Internet to the ComfortClick server public address, which is very slow and creates frequent disconnect).

From the PC, I can connect to the server using Internet Edge : it displays bOS client, and it's working perfectly. So, the PC does see the ComfortClick server IP address. 

From an iPad on the same LAN, a manually created profile with the local IP address is working fine as well. 

So I don't understand why it's not working from bOS configurator. Any ideas ? Anything specific to the configurator that could explain ? I'm using V 4.8.15, and I can't upgrade as I don't want to upgrade my server. 

Thank you very much, 

François 

Hello everyone.

I know there are already posts about it, but I don't see a problem similar to the one I currently have in any of them.

I have a Jigsaw connected to KNX by bus cable.

The problem is that sometimes due to power outages the Jigsaw and the KNX bus go down and not always but on certain occasions when both systems are up. the Jigsaw is not capable of lifting the link with KNX indefinitely and the only solution that can be applied is to restart the Jigsaw and at that moment it raises the link between both systems again.

Is there any way through a program, task or function that allows forcing to deactivate and reactivate the knx connection when it detects that the link is down? Or failing that, to be able to send some kind of Jigsaw restart through some function that “wakes up” the connection with KNX?

Thank you

Hello,

I need to control 10 zones of watering with the following parameters:
- to switch on them for a certain period of time with the ability to change it

- selected devices should switch on one by one with a delay. 

For example, I select in Scene  "zone 1" and setup the timer for 10 minutes, "zone 5" setup the timer for 5 minutes and "zone 6" setup the timer for 10 minutes, so in overall my Scene should run for 25 minutes. I would need to run it in sequence "zone 1" after 10 minutes switch off and with 2 minutes delay start "zone 5" after 5 minutes switch off another delay for 2 minutes and switch on "zone 6" for another 10 minutes.

As I'm a newbie so any help would be appreciated and thank you in advance everyone.

Hi guys,

For the PIN part of the Confirmation Dialog is there a way to have it as a variable? So if you want to change the PIN you change in one place instead of going through all the dialog boxes and update it.

Than you,

Calin

Hello, 

Why if WRITE INTERVAL is 1 second, the data stored is 10 seconds wroten?

Hi guys,

The default baud rate comes as 9600 for the DSC IT-100. Do you have any tips on how to change it to 19200 for virtual keypad? 

Could it be done using the key pad PK5500?

Thanks,

Calin 

Hello everyone

Is there any possibility to make the Comfort Click check the online status of the elements of the KNX bus?

heartbeat?