Hey,

Our client wanted to change ventilation speeds from the thermostat. Ventilation runs on Modbus everything else is on KNX bus.

This may be a really stupid question but... i found that when i put a value for 1byte in bOS 1 then KNX sees it as 3 and value 2 as 5. But in bOS it shows the correct values. Ventilation has 3 speeds that we control (0 is for away, 1 is home, 2 is guests) I made some screenshots. 
In bOS

Shows as correct value in bOS

But in KNX sees it as 3 and value 2 as 5 in knx

Is this normal or am i missing something? 

I got it working though by changing the values in the Thermostat to 3 and 5, there is no problem with value 0 :) . So now every thermostat shows the correct status and from every thermostat they can change the ventilation speeds. But I find it weird that it changes the values like that.

Best regards.

Hi,

I want to reduce the maximum brightness (of lights in a group) to 50% instead of 100% during night.

Anyone an idea how to configure this?

Hello,

I'd like to use the night mode in the buttons (light up and night).

and at the same time i wan't to have the lighting in the bedroom area (toilet, bedrooms, halway,..) to work at ca. 40%.

All lights are DALI dimmable. 

I made a group 3/3/4 night buttons where i put the 4(general) LED - brightness mode in.

What do i have to do in bosconfig for the nightmode buttons and what for the lights to go max. 40%?

Thanks,

Hi dears,, 

I have an important question,, so plz help to answer it,, 

I have hotel project,, the owner needs to know if the rooms are (occupied / empty) as a simple solution, using a KNX 4 binary input modules,,

so my question is can i integrate these knx modules with jigsaw, to read/know each room status as (occupied /empty)?? 

Note: in this KNX system,  I will use KNX Power Supply and KNX 4 binary input modules.. 

Regards,, 

Aladdin Sultan 

I have some some dimming lights (controlled buy dali gateway), they are programmed in ETS and working fine.

Now i'm trying to control theme with comfort click without succes.

I have the following adresses:

3/4/0 switch (switch)

3/4/1 dimming (dimming control)

3/4/2 value (percentage 0-100%)

3/4/3 status (switch)

I used in comfort click the following adress:

Address: 3/4/0 switch

status address: 3/4/2

resutl:

the slide goes directly back to 0

the light does nothing 

Hi, I have the system ABB for Hotel access control

The system ABB used two group address and they are proprietary telegrams

If the composition is known is possible to read the telegram?

Do you have one exemple?

Best regard

Giordano

Hi, 

When I import the .esf file in bOS Configurator I get the error "Error importing EIB devices from .esf" I use ETS5, I tried with very simple knx program.

Hello,

I'm getting many "error connecting to KNX device".

On my first system (Grinder), this is happening from times to times, for a very short period of time (<1 min). 

This is not impacting the good operation of the system, except if this happening when bOS needs to issue a KNX command, but that's very rare, and then I noticed an impact only once.

I thought that maybe this was linked to my IP network that needed some troubleshooting.

But I've got another system, a KNX Jigsaw, for which the KNX error connecting to device is occurring every 2 minutes ! The KNX interface being incorporated into the Jigsaw, this can't be an issue with my environment. 

I'm not using KNX on this Jigsaw, so I just disables the KNX interface, and problem was fixed for me. 

Still I would like to understand how to fix these "error connecting to device" incidents. 

I'm also getting them from times to times for all IP-connected devices: global Caché, Philips Hue, Denon amplifier, etc... 

Thanks,

François 

I am facing a problem cause its the first time I am using Sledgehammer Server . The problem is that via bos Configurator I select the IP/interface automaticlly after searching but when I am trying to just turn on /off a light I am getting an error message saying that device is not connected. I am testing the same channel with USB / knx interface and its working Any help?

We have created allready Scenes in ETS and what I would like to know is how I am going to just call each scene? The scenes Group addreses are allready imported in bOS configurator. Also I would like to create some time tasks, To turn On and Off specific lights which I will  select in specific hours every day. Is it possible and how?

Thank you