Does anyone has tried to work with Loxone and ComfortClick?

BR

Hello,

I am using a demo installation of comfortclick. I am trying to power on/off a Sony monitor through a global cache device (GC-100-12).

I have built an ir receiver with an arduino.

When I press the power on/off button I get these two commands.

A90
Decoded SONY: A90 (12 bits)
Raw (26): 2400 -600 1200 -600 600 -550 1200 -600 600 -600 1150 -600 600 -600 600 -550 1200 -600 600 -600 550 -600 600 -600 600 
A90
Decoded SONY: A90 (12 bits)
Raw (26): 2400 -600 1200 -550 600 -600 1200 -600 600 -550 1200 -600 600 -550 600 -600 1200 -600 600 -550 600 -600 600 -600 600 

From what I see it is the same command send twice, I guess to avoid false positives.

I have configured the command to comfortclick and I can send the command, this is what I get when I receive the command with my ir receiver.

A90
Decoded SONY: A90 (12 bits)
Raw (26): 2400 -550 1250 -500 650 -550 1200 -550 650 -550 1200 -550 600 -600 650 -500 1250 -500 650 -550 650 -550 650 -550 600 

The problem is that the monitor doesn't power up.

I think I need to send the command twice to power it up.

How can I achieve this through comfortclick?

Hello, again. I have just make an integration and I had an issue. One step was programming KNX devices (via USB), then plug Jigsaw , all correct, then I added new KNX devices and when one KNX device was in programming mode (OA 15.15.255) I was unable to program them ETS said two devices in programming mode, I unpluged Jigsaw from KNX bus and then it works. It just happened with OA 15.15.255, then I tried with a device with OA asigned in programing mode and there was no problem.

If I check devices in programing mode with ETS, without any device in programming mode, there no one, but if there is new device (OA 15.15.255) then ETS detect two devices in programing mode (if Jigsaw is plugged).

Regards.

Hi, Maybe I don't understand how does it worls, but if I select horizontal sliding bar changes in vertical mode, and viceversa. In other hand if slider is horizontal (I see vertical) change percent type bar from Rising to Falling, or viceversa, it works but if slider is vertical( I see it horizontal) change percent type bar don't do anything.

Regards and Thanks.

Dear All

I have the server running on widows 7 starter.

I can access the server trough http://<your local IP>/ but from https://<your local IP>/ doesn't work.

I've checked the ports and they aren't blocked in the firewall.

I think this is the reason I can't put my alexa working (in the site appears that "she" makes connection trough https).

Can anyone help me?

Thanks

Hi,

I enjoyed the BOS software.

It fits in my country and my buildings under construction.
The device I'm using: modbus, DSC, Cameras, Global Cache was BOS support.
Lighting control I use of Lutron, if BOS support, my solution will improve better.

If it was, I can pay the fee so you can write more lutron Lutron?: driver integration protocol

Hi

I would love to have yr.no as my weather service. I think they provide better accuracy for Europe compared to yahoo.com

Should be possible to have a module for it.

Check this example page for possibilities: https://www.yr.no/place/Germany/Hamburg/Hamburg/data.html

Also, any plans for integration of IKEA Trådfri products?

Perhaps allowing 3rd party developers to develop plugins for bOS would boost its popularity?

I have several light in a single room each on individual KNX dimmers.  For each I have a group address that I can use to set the value (DPT_Scaling).  I am able to associate these with individual Object Controls with the template of Dimmer and dim them all individually.  I see how I can setup a scene to use a control to set them all to a specific value, but I have to preset that control .  How do I add a single Dimmer control that dims more than one light?

I know I could use ETS5 to create another group address that had more than one dimmer in that but that does not help me if one light is KNX and the other is a different protocol 

Hi,

After changing the port forwarding of my server for security reasons (different port forwarded to the default 443), I lost connection with Amazon Alexa skill.

So, I disabled the skill and tried to enable it again, but I'm constantly getting an error page while opening the authorization page. The authorization page doesn't open (HTTP ERROR 404).

Also, the Controllers page on my profile appear as empty. Despite this errors, I can still access to my server with the remote address...

Is there any bug with the Alexa skill authorization page?

Can BoS server be installed in Windows IoT?, I know that WIoT don't support Windows 32 bits apps.

Regards